Discontinued
Video Transmitter Wireless Colour CCTV
Video Camera with inbuilt 2.4 GHz Video Transmitter & Antenna * Ideal for
Portable applications and for Multiple Monitoring / Observation / Recording
locations * 2.4 GHz VIDEO TRANSMITTER with Micro Antenna * Range in ideal
clear line-of-sight conditions up to 600 metres with High 18 dBi Gain Antennas
Low-Cost Economy Compact
Wireless 2.4 GHz Colour Video Camera / Transmitter
Low-Cost Economy Compact
Wireless Colour CCTV Video Camera with inbuilt Video Transmitter and Micro
Antenna. Ideal for portable applications or virtually unlimited Monitoring /
Observation / Recording locations using multiple Receivers.
Wireless Camera / Transmitter with 6 mm Board Lens and Micro Antenna.
Cat Code: REG12/0.6A
Regulated 12 VDC 0.6 Amp Plug Pack $20
Cat Code: BRKT-1I
Aluminium Swivel Mounting Bracket $8
|
@ 3 metres |
@ 5 metres |
@ 9 metres |
@ 15 metres |
Width of Vision with 6 mm
Lens |
2.4 metres |
4 metres |
7.2 metres |
12 metres |
Additional Lens selection
info here |
|
|
|
|
CAMERA
Image Sensor: 1/3 inch, 512 x 582
pixels, PAL TV System.
Sensitivity: ~ 2 lux (this value
is provided for comparative purposes only) with 6 mm F 1.8 Board Lens.
Signal : Noise Ratio ~ 40 dB.
Resolution: ~ 440 Horizontal
Lines (this value is provided for comparative purposes only).
Low-Smear suitable for Daylight
scenes.
Automatic Electronic Shutter: up
to 1/2 000 second.
Standard 1/4 inch UNC female
thread Top & Bottom for Mounting Bracket.
Accessory Lens: There are no
accessory Lenses for this camera.
Power Requirements: 12 Volts
DC well filtered and Regulated, ~ 120 mA, via 2.1 x 5.5 mm socket, Center Pin =
(+).
Dimensions: ~ 65 mm (L), ~ 32
(W), ~ 29 mm (H), excluding antenna. Antenna ~ 62 mm long, ~ 6 mm diameter.
Total weight ~ 60 grams.
TRANSMITTER
4 Channel Video Transmitter
(Australia 2 Ch) with 'Micro' antenna. Output: 2.4 ~ 2.483 GHz, 10 mW EIRP with
Micro Antenna, SMB connector.
Manufacturer's Experience: 10 +
Years ISO 9001 Certified, made in Taiwan.
Camera is completely
"Self-Contained" no other components required, simply connect to Power
Supply & Video source.
Compatibility:
Transmissions may be received with:
RX-COMPACT 2.4 GHz AV Receiver
RX-Box
Wireless Stereo AV Receiver with Omni Directional Antenna
RX-TFT-56 2.4 GHz AV Receiver & 5" Colour TFT LCD Monitor
USES
Wireless Video RF Transmission
link for covert spy and Cable-Free Wireless CCTV Video Surveillance Cameras,
Quad Screen Processors, Switchers, Monitors, Multiplexers, Video Recorders,
Digital PC Recording.
Portable Wireless Video
Transmitter for covert pinhole video camera surveillance in Shops - Showrooms -
Exhibitions - Work Places - Casinos - Theatres - Concerts - Nightclubs - Outdoor
Events - Cinemas - etc. Portable Home Video Surveillance to monitor Swimming
Pools - Caravans - Boats - etc.
Observation of Horses - Show
Animals - Livestock - etc during transportation in Floats - Trucks - etc.
Automobile Rear Vision and
general observation Video Systems for Caravans - Large Boats - Semi Trailers -
Road Trains - Aircraft - Buses - Modern or Historic choo.. choo..
Trains - etc.
Wireless link for VCRs, PCs,
Lightweight Compact Video Cameras for shooting video program material, Remote
Control: Cars - Boats - Hovercraft - Aircraft, etc.
In Australia Video Transmitters
may be legally used without a licence within the *LIPD 2400 ~ 2463 MHz Band and
10 mW *EIRP limit.
RANGE
Depends on surroundings,
obstructions, buildings, antenna gain, other transmitters, EMI & RFI in the
vicinity.
In ideal, clear, Line-of-Sight
conditions with Vertical 3 dBi Whip antenna on TX
Vertical 3 dBi Whip antenna on
Receiver up to ~ 100 metres.
Correctly matched and aligned 18
dBi antenna on Receiver up to ~ 600 metres.
Due to the nature of Radio
Signals results are unpredictable (in the same manner as Mobile / Cellular
Telephones) signals reflected from surrounding objects arriving at Receiver
antenna may Add-to or Subtract-from the direct signal from Transmitter.
Directional antennas may reduce affect of reflected signals.
RECEIVER ANTENNAS
Range and Signal to Noise Ratio
(SNR) may be improved by increasing gain of antenna on Receiver and/or
Transmitter (in Australia TX may only be fitted with 3 dBi antenna). For
maximum signal transfer TX and RX antennas should be the same polarity, that is
both oriented Vertically or Horizontally.
 |
Cat Code: Ant-Stub
(Net) $30
0 dBi gain, ~ 50 ohms
impedance.
Length: ~ 52 mm.
Diameter: ~ 9 mm. Weight: ~ 6 grams.
Pictured fitted to TX-CAM
3.
SMA male Connector.
|
 |
Cat
Code: Ant-Whip (Gold)
(A) $12
/ (B) $15
Cat Code: Ant-Whip/BP Bulk
Pak 30 pieces (Net) $120
~ 3 dBi gain, ~ 50 ohms impedance.
Length: ~ 107 mm straight ~ 87 mm
folded. Diameter: ~ 9 mm. Weight: ~ 11 grams.
SMA male Connector.
|
 |
Cat
Code: Ant-W5dB (Gold)
(A) $24
/ (B) $30
~ 5 dBi gain, ~ 50 ohms
impedance.
Length: ~ 195 mm straight ~
170 mm folded. Diameter: ~ 13 mm @ Base ~ 6 mm @ Top. Weight: ~ 30
grams.
SMA male Connector.
|
 |
Cat
Code: Ant-W9dB (Gold)
(A) $103 / (B) $129
~ 9 dBi gain, ~ 50 ohms
impedance.
Length: ~ 610 mm ~ 825 mm with
Base Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center
section ~ 24 mm top cap. Weight: ~ 470 grams ~ 730 grams with Mounting
Tube & Clamps/Brackets.
Supplied with Base Mount Tube and Clamps/Brackets for
surface or Tubular Mast mounting. N female Connector. <Adaptors
& Extension Cables>
|
 |
Cat
Code: Ant-W12dB (Gold)
(A) $127
/ (B) $159
~ 12 dBi gain, ~ 50 ohms impedance.
Length: ~ 1210 mm ~ 1425 mm with Base
Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center section ~ 24 mm
top cap. Weight: ~ 670 grams ~ 930 grams with Mounting Tube &
Clamps/Brackets.
Supplied with Base Mount Tube and
Clamps/Brackets for surface or Tubular Mast mounting. N female
Connector. <Adaptors &
Extension Cables>
|
 |
Cat Code: Ant-Y8
(Gold)
(A) $71
/ (B) $89
~ 8 dBi gain, 6 Element. Dimensions (excluding Clamps) ~ 290 x 95 x 35
mm, ~ 530 grams.
Cat Code: Ant-Y12 (Gold)
(A) $95
/ (B) $119
~ 12 dBi gain, 10 Element. Dimensions (excluding Clamps) ~ 430 x 95
x 35 mm, ~ 600 grams.
Cat Code: Ant-Y15 (Gold)
(A) $103 /
(B) $129
~ 15 dBi gain, 15 Element. Dimensions (excluding Clamps) ~ 650 x 95
x 35 mm, ~ 680 grams.
Common Specifications:
2.4 ~ 2.5 GHz, Dipole ~ 50 ohms impedance, ~ 500 mm RG-142 Coax cable.
Supplied with ~ 140 x 70 mm Aluminium mounting plate, Clamps, etc.
Pictured in Vertical Polarity orientation * Mast not included. SMA
male Connector.
|
 |
Cat Code: Ant-F8N
(Gold)
(A) $63
/ (B) $79
COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~ 8 dBi gain, ~ 50 ohm
impedance. Beamwidth: ~ 60º (H) ~ 70º (V).
Supplied with versatile
selection of mounting hardware for Wall/Ceiling mounting & Tubular
Mast Clamp. Dimensions (excludes Socket & Brackets) ~ 95 (W) ~ 110
(H) ~ 30 mm (D), ~ 260 grams.
Pictured in Vertical Polarity orientation.
N female Connector. <Adaptors &
Extension Cables>
|
 |
Cat Code: Ant-P10
(Gold)
(A) $87
/ (B) $109
COMPACT
Semi-Parabolic 2.3 ~ 2.5 GHz, ~ 10.5 dBi gain, ~ 50 ohm impedance.
Beamwidth: ~ 30º (H) ~ 60º (V).
Supplied with Tubular
Mast Clamp. Dimensions (excludes Socket & Brackets) ~ 275 (W) ~ 90
(H) x ~ 58 mm (D), ~ 235 grams.
Pictured in Vertical
Polarity orientation.
SMA female
Connector. <Adaptors & Extension
Cables>
|
 |
Cat Code: Ant-F12
(Gold)
(A) $95
/ (B) $119
COMPACT Flat Antenna 2.3
~ 2.5 GHz, ~ 12 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 28º (H) ~
70º (V).
Supplied with versatile
selection of mounting hardware for Wall/Ceiling mounting & two
Tubular Mast Clamps.
Dimensions (excludes
Socket & Brackets) ~ 95 (W) ~ 212 (H) ~ 30 mm (D), ~ 500 grams.
(Shipping weight 1010 grams)
Pictured in Vertical
Polarity orientation.
N female Connector.
<Adaptors & Extension Cables>
|
 |
Cat Code: Ant-F16
(Gold)
(A) $127
/ (B) $159
COMPACT Flat Antenna 2.3
~ 2.5 GHz, ~ 16 dBi gain, ~ 50 ohm impedance.
Beamwidth: ~ 27º (H) ~
60º (V).
Supplied with versatile
selection of mounting hardware for Wall/Ceiling mounting & two
Tubular Mast Clamps.
Dimensions (excludes
Socket & Brackets) ~ 135 (W) ~ 455 (H) ~ 30 mm (D), ~ 740 grams.
Pictured in Vertical
Polarity orientation
N female Connector. <Adaptors
& Extension Cables>
|
 |
Cat
Code: Ant-F18 (Gold)
(A) $167
/ (B) $209
COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~
18 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 45º (H) ~ 75º (V).
Supplied with versatile selection of
mounting hardware for Wall/Ceiling mounting & two Tubular Mast
Clamps.
Dimensions (excludes Socket &
Brackets) ~ 262 (W) ~ 262 (H) ~ 38 mm (D), ~ 950 grams.
Pictured in Vertical Polarity
orientation.
N female Connector. <Adaptors
& Extension Cables>
|
 |
Cat
Code: Ant-P18G (A)
$95 / (B) $119
2.4 ~ 2.5 GHz, ~ 18 dBi gain sectional
Grid Parabolic, ~ 50 ohm impedance Dipole. Beamwidth ~ 25º in vertical
polarity mode, Front to Back ratio ~ 20 dB. Fitted with ~ 750 mm RG-8/U
Coax cable.
Reflector ~ 390 x ~ 545 mm. Weight ~
1.7 kilograms. Supplied with Hor/Vert Clamp mounting hardware.
Carriage in an Air Satchel $13, via
Post $35.
Pictured in Vertical Polarity
orientation * Mast not included. Gold Irridite coated version
pictured, we now stock a more durable Galvanised version only.
N male Connector. <Adaptors
& Extension Cables>
|
 |
Cat
Code: SMAm-Nf (Net) $10
SMA male to N female. Suitable for P18G antenna. |
 |
Cat
Code: SMAm-Nm (Net) $10
SMA male to N male. Suitable for F8N,
W9dB, F12, W12dB, F16 & F18 antennas.
|
 |
Cat
Code: SMAm-m (Net) $10
SMA male to SMA male. Suitable for P10
antenna.
|
 |
Cat Code: Cable-178/30
(Gold)
(A) $24
/ (B) $30
30 cm RG-178 Coax cable
with SMA male & female connectors.
Cat Code: Cable-316/50
(Net) $35
50 cm RG-316 Coax cable
with SMA male & female connectors.
Attenuation ~ 1 dB @ 3
GHz.
|
 |
Cat Code: Coax178/SMA
(Net) $10
~ 10 cm RG-178 Coax cable
with SMA male connector.
|
 |
Cat Code: Cable-223/450
(Gold)
(A) $63
/ (B) $79
~ 450 cm Coax Cable with
SMA male & female connectors. Attenuation ~ 0.75 dB/metre @ 2 GHz.
Cat Code: Cable-223/450N
(Gold)
(A) $63
/ (B) $79
not pictured
~ 450 cm Coax Cable with
SMA & N male connectors. Attenuation ~ 0.55 dB/metre @ 3 GHz. Suitable
for F8N, W9dB, F12, W12dB, F16 & F18 antennas.
|
|
Parabolic Yagi &
Flat are directional antennas. Whip antennas when used vertically are
for most practical purposes omni or non directional.
To maximise 'Range'
minimise the length of Coax Cable between Antenna and TX/RX.
|
|
Antenna Gain... what does
it mean ??? a simplified explanation
Received signal strength
from an antenna with 3 dBi gain will be double that from an antenna that
has 0 dBi gain, received signal strength from a 6 dBi will be double that
from a 3 dBi and so on... An increase in antenna gain of 3 dBi is
approximately equal to doubling the transmitter output, received signal
strength or range can be increased by raising antenna gain or transmitter
output. Range can be doubled by either increasing antenna gain by 6 dBi or
quadrupling the transmitter output.
The maximum allowed 2.4
GHz LIPD Video Transmitter output power is 10 milliwatts (mW) EIRP (in
Australia), increasing transmitter output is illegal and therefore not an
option.
Increasing the gain of
the receiver antenna is an alternative to increasing transmitter output.
In very simple terms: increasing antenna gain from 0 dBi to
3 dBi is equivalent to raising the output power of a 10 mW transmitter to
~ 20 mW. (5 dBi to ~ 33 mW) ( 8 dBi to ~ 66 mW) (12 dBi to ~ 160 mW) (15
dBi to ~ 320 mW) (18 dBi to ~ 640 mW)
|
** Information
plagiarised from this page may be found on 'copy-cat' Web Sites **
Use your Browser "Back
Button" to return to previous page