Pinhole tiny Wireless Security Camera
Video Transmitter & Colour Pinhole CCTV Video Camera * High-Sensitivity High Signal:Noise Ratio Colour Pinhole CCD Camera with Wireless 4 Channel 2.4 GHz Video Sender Transmitter & Micro Antenna * Ideal for portable, discreet, covert applications and for Multiple Monitoring / Observation / Recording locations * Compact 12 VOLT DC Colour CCTV Video Camera & 2.4 GHz VIDEO SENDER / TRANSMITTER with Micro Antenna * Range in ideal clear line-of-sight conditions up to 600 metres with High 18 dBi Gain Antenna

High-Sensitivity High Signal-to-Noise Ratio Wireless 2.4 GHz Colour Video Camera with 5 mm Pinhole Lens * 4 Channel 2.4 GHz Video Transmitter with Micro Antenna

Pinhole tiny Wireless Security Camera

Pinhole tiny Wireless Security Camera

TX-CAM2P High Sensitivity * High Signal:Noise Ratio
Compact 2.4 GHz 4 Channel Wireless Colour PINHOLE CCTV Video Camera with inbuilt Video Transmitter and Micro Antenna.

Ideal for portable & discreet / covert applications or virtually unlimited Monitoring / Observation / Recording locations using multiple Receivers.

REG12/0.6A Regulated Plug Pack (Net) $20

BRKT-1I Aluminium Swivel Mounting Bracket $8

CAMERA Image Sensor 1/4 inch LOW BLEMISH CCD, 512 x 582 pixels. PAL TV System. Sensitivity: ~ 3 lux @ F1.2 (this value is provided for comparative purposes only). Signal : Noise Ratio ~ 48 dB.

Resolution: ~ 440 Horizontal Lines (this value is provided for comparative purposes only).

Automatic Electronic Shutter: 1/50 ~ 1/100 000 second, 20 ms ~ 10 microseconds. Standard 1/4 inch UNC female thread Top & Bottom for Mounting Bracket.

Accessory Lenses: None.

Power Requirements: 12 Volts DC well filtered and Regulated, ~ 160 mA, via 2.1 x 5.5 mm socket, Center Pin = (+). Dimensions: ~ 55 mm (L), ~ 32 (W), ~ 29 mm (H), excluding antenna. Antenna ~ 62 mm long, ~ 6 mm diameter. Total weight ~ 60 grams.

VIDEO TRANSMITTER 4 Channel (Australia 2 Ch) with 'Micro' antenna. Output: 2.4 ~ 2.483 GHz, 10 mW EIRP with Micro Antenna, SMB connector.

Pictured with Micro Plug-In Antenna (supplied)

Connection info here

 

@ 3 metres @ 5 metres @ 9 metres @ 15 metres

Width of Vision with 5 mm Lens

2.2 metres 3.6 metres 6.5 metres 10.8 metres

Additional Lens info

       

Manufacturer's Experience: 10 + Years ISO 9001 Certified, made in Taiwan.

Camera is completely "Self-Contained" no other components required, simply connect to Power Supply & Video source.

Compatibility: Transmissions may be received with:

Compact VIDEO & AUDIO 2.4 GHz RECEIVER
RX-COMPACT
2.4 GHz AV Receiver

VIDEO & STEREO AUDIO 2.4 GHz RECEIVER
RX-Box Wireless Stereo AV Receiver with Omni Directional Antenna

Video Transmitter Receiver built into 5.6 inch LCD TFT Colour Monitor
RX-TFT-56
2.4 GHz AV Receiver & 5" Colour TFT LCD Monitor

USES

Wireless Video RF Transmission link for covert spy and Cable-Free Wireless CCTV Video Surveillance Cameras, Quad Screen Processors, Switchers, Monitors, Multiplexers, Video Recorders, Digital PC Recording.

Portable Wireless Video Transmitter for covert pinhole video camera surveillance in Shops - Showrooms - Exhibitions - Work Places - Casinos - Theatres - Concerts - Nightclubs - Outdoor Events - Cinemas - etc. Portable Home Video Surveillance to monitor Swimming Pools - Caravans - Boats - etc.

Observation of Horses - Show Animals - Livestock - etc during transportation in Floats - Trucks - etc.

Automobile Rear Vision and general observation Video Systems for Caravans - Large Boats - Semi Trailers - Road Trains - Aircraft - Buses - Modern or Historic choo.. choo.. Trains - etc.

Wireless link for VCRs, PCs, Lightweight Compact Video Cameras for shooting video program material, Remote Control: Cars - Boats - Hovercraft - Aircraft, etc.

In Australia Video Transmitters may be legally used without a licence within the *LIPD 2400 ~ 2463 MHz Band and 10 mW *EIRP limit.

RANGE

Depends on surroundings, obstructions, buildings, antenna gain, other transmitters, EMI & RFI in the vicinity.

In ideal, clear, Line-of-Sight conditions with Vertical 3 dBi Whip antenna on TX

Vertical 3 dBi Whip antenna on Receiver up to ~ 100 metres.

Correctly matched and aligned 18 dBi antenna on Receiver up to ~ 600 metres.

Due to the nature of Radio Signals results are unpredictable (in the same manner as Mobile / Cellular Telephones) signals reflected from surrounding objects arriving at Receiver antenna may Add-to or Subtract-from the direct signal from Transmitter. Directional antennas may reduce affect of reflected signals.

RECEIVER ANTENNAS

Range and Signal to Noise Ratio (SNR) may be improved by increasing gain of antenna on Receiver and/or Transmitter (in Australia TX may only be fitted with 3 dBi antenna). For maximum signal transfer TX and RX antennas should be the same polarity, that is both oriented Vertically or Horizontally.

Ant-Stub video transmitter

Ant-Stub (Net) $30

0 dBi gain, ~ 50 ohms impedance.

Length: ~ 52 mm. Diameter: ~ 9 mm. Weight: ~ 6 grams.

Pictured fitted to TX-CAM 3.

SMA male Connector.

Folding Straight or Right-Angle 2.4 GHz 3 dBi Gain Microwave Whip Antenna

Ant-Whip (Gold) (A) $12 / (B) $15

Cat Code: Ant-Whip/BP Bulk Pak 30 pieces (Net) $120

~ 3 dBi gain, ~ 50 ohms impedance.

Length: ~ 107 mm straight ~ 87 mm folded. Diameter: ~ 9 mm. Weight: ~ 11 grams.

SMA male Connector.

SMA Male Connector

Ant-W5dB (Gold) (A) $24 / (B) $30

~ 5 dBi gain, ~ 50 ohms impedance.

Length: ~ 195 mm straight ~ 170 mm folded. Diameter: ~ 13 mm @ Base ~ 6 mm @ Top. Weight: ~ 30 grams.

SMA male Connector.

~ 9 dBi gain, N female Connector.

Ant-W9dB (Gold) (A) $103 / (B) $129

~ 9 dBi gain, ~ 50 ohms impedance.

Length: ~ 610 mm ~ 825 mm with Base Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center section ~ 24 mm top cap. Weight: ~ 470 grams ~ 730 grams with Mounting Tube & Clamps/Brackets.

Supplied with Base Mount Tube and Clamps/Brackets for surface or Tubular Mast mounting. N female Connector. <Adaptors & Extension Cables>

~ 12 dBi gain, N female Connector

Ant-W12dB (Gold) (A) $127 / (B) $159

~ 12 dBi gain, ~ 50 ohms impedance.

Length: ~ 1210 mm ~ 1425 mm with Base Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center section ~ 24 mm top cap. Weight: ~ 670 grams ~ 930 grams with Mounting Tube & Clamps/Brackets.

Supplied with Base Mount Tube and Clamps/Brackets for surface or Tubular Mast mounting. N female Connector.  <Adaptors & Extension Cables>

High Gain Directional Yagi  2.4 GHz Microwave

Ant-Y8 (Gold) (A) $71 / (B) $89
~ 8 dBi gain, 6 Element. Dimensions (excluding Clamps) ~ 290 x 95 x 35 mm, ~ 530 grams.

Ant-Y12 (Gold) (A) $95 / (B) $119
~ 12 dBi gain, 10 Element. Dimensions (excluding Clamps) ~ 430 x 95 x 35 mm, ~ 600 grams.

Ant-Y15 (Gold) (A) $103 / (B) $129
~ 15 dBi gain, 15 Element. Dimensions (excluding Clamps) ~ 650 x 95 x 35 mm, ~ 680 grams.

Common Specifications: 2.4 ~ 2.5 GHz, Dipole ~ 50 ohms impedance, ~ 500 mm RG-142 Coax cable. Supplied with ~ 140 x 70 mm Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included. SMA male Connector.

COMPACT Flat Antenna 2.3 ~ 2.5 GHz

Ant-F8N (Gold) (A) $63 / (B) $79
COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~ 8 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 60 (H) ~ 70 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & Tubular Mast Clamp. Dimensions (excludes Socket & Brackets) ~ 95 (W) ~ 110 (H) ~ 30 mm (D), ~ 260 grams.
Pictured in Vertical Polarity orientation.
N female Connector
. <Adaptors & Extension Cables>

COMPACT Semi-Parabolic 2.3 ~ 2.5 GHz

Ant-P10 (Gold) (A) $87 / (B) $109

COMPACT Semi-Parabolic 2.3 ~ 2.5 GHz, ~ 10.5 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 30 (H) ~ 60 (V).

Supplied with Tubular Mast Clamp. Dimensions (excludes Socket & Brackets) ~ 275 (W) ~ 90 (H) x ~ 58 mm (D), ~ 235 grams.

Pictured in Vertical Polarity orientation.

SMA female Connector. <Adaptors & Extension Cables>

COMPACT Flat Antenna 2.3 ~ 2.5 GHz

Ant-F12 (Gold) (A) $95 / (B) $119

COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~ 12 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 28 (H) ~ 70 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & two Tubular Mast Clamps.

Dimensions (excludes Socket & Brackets) ~ 95 (W) ~ 212 (H) ~ 30 mm (D), ~ 500 grams. (Shipping weight 1010 grams)

Pictured in Vertical Polarity orientation.

N female Connector. <Adaptors & Extension Cables>

COMPACT Flat Antenna 2.3 ~ 2.5 GHz

Ant-F16 (Gold) (A) $127 / (B) $159

COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~ 16 dBi gain, ~ 50 ohm impedance.

Beamwidth: ~ 27 (H) ~ 60 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & two Tubular Mast Clamps.

Dimensions (excludes Socket & Brackets) ~ 135 (W) ~ 455 (H) ~ 30 mm (D), ~ 740 grams.

Pictured in Vertical Polarity orientation

N female Connector. <Adaptors & Extension Cables>

COMPACT Flat Indoor or OUTDOOR Antenna 2.3 ~ 2.5 GHz

Ant-F18 (Gold) (A) $167 / (B) $209

COMPACT Flat Antenna 2.3 ~ 2.5 GHz, ~ 18 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 45 (H) ~ 75 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & two Tubular Mast Clamps.

Dimensions (excludes Socket & Brackets) ~ 262 (W) ~ 262 (H) ~ 38 mm (D), ~ 950 grams.

Pictured in Vertical Polarity orientation.

N female Connector. <Adaptors & Extension Cables>

Ant-P18 pictured in Vertically Polarised position 2.4 ~ 2.5 GHz

Ant-P18G (A) $95 / (B) $119

2.4 ~ 2.5 GHz, ~ 18 dBi gain sectional Grid Parabolic, ~ 50 ohm impedance Dipole. Beamwidth ~ 25 in vertical polarity mode, Front to Back ratio ~ 20 dB. Fitted with ~ 750 mm RG-8/U Coax cable.

Reflector ~ 390 x ~ 545 mm. Weight ~ 1.7 kilograms. Supplied with Hor/Vert Clamp mounting hardware.

Carriage in an Air Satchel $13, via Post $35.

Pictured in Vertical Polarity orientation * Mast not included. Gold Irridite coated version pictured, we now stock a more durable Galvanised version only.

N male Connector. <Adaptors & Extension Cables>


ADAPTORS

SMA male to N female

SMAm-Nf (Net) $10

SMA male to N female. Suitable for P18G antenna.

SMA male to N male

SMAm-Nm (Net) $10

SMA male to N male. Suitable for F8N, W9dB, F12, W12dB, F16 & F18 antennas.

SMA male to SMA male

SMAm-m (Net) $10

SMA male to SMA male. Suitable for P10 antenna.

50 centimetre Extension Cable for Transmitters

Cable-178/30 (Gold) (A) $24 / (B) $30

30 cm RG-178 Coax cable with SMA male & female connectors.

Cat Code: Cable-316/50 (Net) $35

50 cm RG-316 Coax cable with SMA male & female connectors.

Attenuation ~ 1 dB @ 3 GHz.

~ 10 cm RG-178 Coax cable with SMA male connector.

Coax178/SMA (Net) $10

~ 10 cm RG-178 Coax cable with SMA male connector.

~ 4.5 metre Coax Cable for Transmitter

Cable-223/450 (Gold) (A) $63 / (B) $79

~ 450 cm Coax Cable with SMA male & female connectors. Attenuation ~ 0.75 dB/metre @ 2 GHz.

Cable-223/450N (Gold) (A) $63 / (B) $79
not pictured

~ 450 cm Coax Cable with SMA & N male connectors. Attenuation ~ 0.55 dB/metre @ 3 GHz. Suitable for F8N, W9dB, F12, W12dB, F16 & F18 antennas.

Parabolic Yagi & Flat are directional antennas. Whip antennas when used vertically are for most practical purposes omni or non directional.

To maximise 'Range' minimise the length of Coax Cable between Antenna and TX/RX.

Antenna Gain... what does it mean ??? a simplified explanation

Received signal strength from an antenna with 3 dBi gain will be double that from an antenna that has 0 dBi gain, received signal strength from a 6 dBi will be double that from a 3 dBi and so on... An increase in antenna gain of 3 dBi is approximately equal to doubling the transmitter output, received signal strength or range can be increased by raising antenna gain or transmitter output. Range can be doubled by either increasing antenna gain by 6 dBi or quadrupling the transmitter output.

The maximum allowed 2.4 GHz LIPD Video Transmitter output power is 10 milliwatts (mW) EIRP (in Australia), increasing transmitter output is illegal and therefore not an option.

Increasing the gain of the receiver antenna is an alternative to increasing transmitter output.
In very simple terms: increasing antenna gain from 0 dBi to 3 dBi is equivalent to raising the output power of a 10 mW transmitter to ~ 20 mW. (5 dBi to ~ 33 mW) ( 8 dBi to ~ 66 mW) (12 dBi to ~ 160 mW) (15 dBi to ~ 320 mW) (18 dBi to ~ 640 mW) 

* LIPD = Low Interference Potential Devices. * EIRP = Equivalent Isotropically Radiated Power. Source: Australian Communications Authority
Click below for information on Frequencies & Power Limits
http://www.aca.gov.au/legal/licence/class/lipd.htm