2.4 GHz Video Audio Receiver Switcher Colour Monitor

2.4 GHz Video Audio Receiver Switcher Colour Monitor

RX-TFT-56 Wireless 2.4 GHz 4 Channel Video & Audio Receiver / Switcher

AND

Audio Video 5" LCD TFT Colour Monitor.

Manual or Automatic Sequential Switching.

12 Volts DC or Mains powered using REG12/1.5A or Universal Power Supply.

Cable-AV/Rf AV Input Cable RCA female (Net) $8

Cable-RCA2 AV Cable $6

 

RX-TFT-56SMA $449 - Special model fitted with SMA antenna input for use with High-Gain Antennas to extend range.

 

Business
Observe showrooms, warehouse, offices, doors, etc without the need to install expensive and inflexible wiring.
Receive images to multiple remote Monitors for general surveillance and observation.
Use in multiple Advertising Displays to display message from a Video Player, PC, etc.

Entertainment
View & Listen all over the house and even out on the patio or pool area from a central source.

Safety
See who is outside your door using a Video Camera and Transmitter.
Monitor your baby, your children, the swimming pool, the elderly, ill or recuperating using your Camcorder or a CCTV Video Camera & Transmitter.
Observe your home or office using up to four transmitters and cameras (in Australia maximum is two transmitters).

Features:
Display: Colour 5 Inch.
TV System: CCIR / PAL (Australia/UK).
Four Channel Receiver, single channel selection or Automatic Sequential Switching with ~ 4 second dwell.


Audio & Video Input/Output for: DVD Player, Satellite TV, Reversing Video Camera, Tuner, Camcorder, Surveillance Video Camera, PC DVD / MPEG / AVI Playback, TV Set (AV), Switcher, Video Monitor, PC Audio/Video Capture Card, VCR, DVR, etc.

Receiver Specifications:
ISM Band: 2.4 ~ 2.483 GHz, 4 channels.
Antenna: Whip, non removable folding type.
** RX-TFT-56SMA ONLY has SMA antenna input socket to extend range with High-Gain antennas listed below.
Demodulation Method: FM.
Oscillator: P.L.L. (Phase Locked Loop).
Sensitivity: -92 dbm.

Display Specifications:
Colour ~ 5 inch / ~ 130 mm (diagonal) Thin Film Transistor (TFT) Liquid Crystal Display (LCD).
Picture Elements (Pixels): 600 (H) x 234 (V).
Active Area: ~ 113 mm x ~ 75 mm.
Sensitivity (Video): 1.0 v p-p, negative sync.

Inputs:
Composite Video standard 75 ohm and Line Level Audio, via 3.5 mm 3 contact phono socket on Right side, compatible with CCIR / PAL (Australia/UK) TV System.
** RX-TFT-56SMA ONLY - is fitted with SMA female antenna input socket, attached Whip Antenna is not connected.

Outputs:
Composite Video standard 75 ohm and Line Level Audio, via 3.5 mm 3 contact phono socket on Right side.
Speaker, mini internal.

Controls:
Rotary type on Right Side.
Brightness.
Volume.

Press Buttons:
Front Panel.
Power On/Off / AV Input selector.
Channel Select 1, 2, 3 & 4, Auto Sequential Switching On/Off.

Switches:
DIP type on Right Side.
Channel Select 1, 2, 3, & 4 for Auto Scan function.
Auto Scan Dwell Duration 2, 4, 8 or 12 seconds.

Indicators:
Front Panel.
Channel 1, 2, 3 & 4.
Power / AV Input.

Power Requirements:
12 Volts DC Regulated, ~ 950 milliamps, 2.1 x 5.5 mm DC socket, Center Pin = (+) located on Left Side. *** 12 Volt DC Regulated 1.5 Amp Power Supply recommended.

Dimensions:
~ 155 mm (W) ~ 116 mm (H) ~ 45 mm (D).
Weight ~ 450 grams.

Mounting:
As pictured on a flat horizontal surface with the rear mounted folding support 'Leg'.
Alternatively via 1/4" UNC threaded mounting point at bottom center of Case.

To View Detailed Product InformationVideo Transmitter Receiver built into 5.6 inch LCD TFT Colour Monitor with Audio * Compact 2.4 GHz * Wireless AV Receiver  / Monitor for: Covert Surveillance, portable Baby Monitoring, VCRs, Satellite TV, DVD, PCs, Pay TV, MDS, Cable TV, Remote Control: Cars - Boats - Hovercraft, Portable CCTV Video Surveillance * Wireless Audio & Composite Video for Covert Tiny Hidden Pinhole Spy Video Cameras & Reception of CCTV Surveillance Video from Cameras, Switchers, Quad Screen Processors, Multiplexers, Monitors.  Range with 10 mW EIRP Transmitter in ideal clear line-of-sight conditions up to 100 metres - up to 1.6 kilometres with our High Gain Antennas.this is a PDF document and may take several minutes to download, it will open in a New Window so you may continue browsing.

Manufacturer's Experience: 10 + Years ISO 9001 Certified, made in Taiwan.

Compatibility:

Receives transmissions from: TX-MOD 2, TX-MOD 3, TX-ELECTRET, TX-BNC, TX-AV050, TX-AV500, TX-AV1000, TX-AV2000, TX-CAM2, TX-CAM2P & TX-CAM3.

Receives transmissions of Video & Left Audio Channel from TX-Box, TX-Mini & TX/RX AV System II.

ANTENNAS suitable for Cat Code: RX-TFT-56SMA Only !

Range and Signal to Noise Ratio (SNR) may be improved by increasing gain of antenna on Receiver and/or Transmitter. For maximum signal transfer TX and RX antennas should be the same polarity, that is both oriented Vertically or Horizontally.

Video Audio Transmitter SMA Antenna

Ant-Stub $5

0 dBi gain, ~ 50 ohms impedance.

Length: ~ 52 mm. Diameter: ~ 9 mm. Weight: ~ 6 grams.

SMA male Connector.

2.4 GHz Antenna

Ant-Whip $15

~ 3 dBi gain, ~ 50 ohms impedance.

Length: ~ 145 mm straight ~124 mm folded. Diameter: ~ 9 & 10 mm. Weight: ~ 16 grams.

SMA male Connector.

~ 5 dBi gain antenna

Ant-W5dB $20

~ 5 dBi gain, ~ 50 ohms impedance.

Length: ~ 195 mm straight ~ 170 mm folded. Diameter: ~ 13 mm @ Base ~ 6 mm @ Top. Weight: ~ 30 grams.

SMA male Connector.

~ 9 dBi gain N female Connector 2.4 ghz antenna

Ant-W9dB $99

~ 9 dBi gain, ~ 50 ohms impedance.

Length: ~ 610 mm ~ 825 mm with Base Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center section ~ 24 mm top cap. Weight: ~ 470 grams ~ 730 grams with Mounting Tube & Clamps/Brackets.

Supplied with Base Mount Tube and Clamps/Brackets for surface or Tubular Mast mounting. N female Connector. <Adaptors & Extension Cables>

~ 12 dBi gain N female Connector 2.4 ghz antenna

Ant-W12dB $129

~ 12 dBi gain, ~ 50 ohms impedance.

Length: ~ 1210 mm ~ 1425 mm with Base Mount Tube. Diameter: ~ 42 mm @ Base ~ 22 mm main center section ~ 24 mm top cap. Weight: ~ 670 grams ~ 930 grams with Mounting Tube & Clamps/Brackets.

Supplied with Base Mount Tube and Clamps/Brackets for surface or Tubular Mast mounting. N female Connector.  <Adaptors & Extension Cables>

High Gain Directional Yagi  2.4 GHz Microwave Antenna

Ant-Y8 $69
Yagi ~ 8 dBi gain, ~ 50 ohms impedance. ~ 500 mm RG-142 Coax cable. Dimensions (excluding Clamps) ~ 290 x 95 x 35 mm, ~ 530 grams.

Ant-Y12 $89 Discontinued
Yagi
~ 12 dBi gain, ~ 50 ohms impedance. ~ 500 mm RG-58 Coax cable. Dimensions (excluding Clamps) ~ 430 x 95 x 35 mm, ~ 600 grams.

Ant-Y15 $99
Yagi
~ 15 dBi gain, ~ 50 ohms impedance. ~ 500 mm RG-58 Coax cable. Dimensions (excluding Clamps) ~ 650 x 95 x 35 mm, ~ 680 grams.

Common Specifications: 2.4 ~ 2.5 GHz Dipole. Supplied with ~ 140 x 70 mm Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector. <Adaptors & Extension Cables>

High Gain Directional Yagi 2.4 GHz Microwave Antenna

Ant-Y8C $89

Compact Yagi 2.4 ~ 2.5 GHz, ~ 8 dBi gain, ~ 50 ohms impedance. Beamwidth: E70, H90.

Dimensions (excluding Clamps) ~ 190 mm, ~ 75 mm diameter, ~ 500 grams, ~ 500 mm RG-58 Coax cable. Supplied with Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector. <Adaptors & Extension Cables>

High Gain Directional 2.4 GHz Microwave Antenna
Yagi 2.4 GHz Microwave Antenna

Ant-Y10C $99

COMPACT Yagi 2.4 ~ 2.5 GHz, ~ 10 dBi gain, ~ 50 ohms impedance. Beamwidth: E44, H56.

Dimensions (excluding Clamps) ~ 280 mm, ~ 75 mm diameter, ~ 500 grams, ~ 500 mm RG-58 Coax cable. Supplied with Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector.

Directional 2.4 GHz Microwave Antenna

Ant-Y12C $109

Yagi 2.4 ~ 2.5 GHz, ~ 12 dBi gain, ~ 50 ohms impedance. Beamwidth: E35, H40.

Dimensions (excluding Clamps) ~ 450 mm, ~ 75 mm diameter, ~ 650 grams, ~ 500 mm RG-58 Coax cable. Supplied with Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector. <Adaptors & Extension Cables>

2.4 GHz Microwave Antenna
Directional Yagi 2.4 GHz Microwave Antenna

Ant-Y16C $119

Yagi 2.4 ~ 2.5 GHz, ~ 16 dBi gain, ~ 50 ohms impedance. Beamwidth: E28, H28.

Dimensions (excluding Clamps) ~ 650 mm, ~ 75 mm diameter, ~ 750 grams, ~ 500 mm RG-58 Coax cable. Supplied with Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector. <Adaptors & Extension Cables>

2.4 GHz Microwave Antenna
2.4 GHz Microwave Antenna High Gain Directional Yagi

Ant-Y17.5C $149

Yagi Antenna 2.4 ~ 2.5 GHz, ~ 17.5 dBi gain, ~ 50 ohms impedance. Beamwidth: E23, H24.

Dimensions (excluding Clamps) ~ 850 mm, ~ 75 mm diameter, ~ 800 grams, ~ 500 mm RG-58 Coax cable. Supplied with Aluminium mounting plate, Clamps, etc. Pictured in Vertical Polarity orientation * Mast not included.

SMA male Connector. <Adaptors & Extension Cables>

2.4 GHz Microwave Flat Antenna

Ant-F16 $129

COMPACT Flat 2.3 ~ 2.5 GHz, ~ 16 dBi gain, ~ 50 ohm impedance.

Beamwidth: ~ 27 (H) ~ 60 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & two Tubular Mast Clamps.

Dimensions (excludes Socket & Brackets) ~ 135 (W) ~ 455 (H) ~ 30 mm (D), ~ 740 grams.

Pictured in Vertical Polarity orientation

N female Connector. <Adaptors & Extension Cables>

2.4 GHz Microwave Antenna Flat Indoor or OUTDOOR

Ant-F18 $149

COMPACT Flat 2.3 ~ 2.5 GHz, ~ 18 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 45 (H) ~ 75 (V).

Supplied with versatile selection of mounting hardware for Wall/Ceiling mounting & two Tubular Mast Clamps.

Dimensions (excludes Socket & Brackets) ~ 262 (W) ~ 262 (H) ~ 38 mm (D), ~ 950 grams.

Pictured in Vertical Polarity orientation.

N female Connector. <Adaptors & Extension Cables>

Semi-Parabolic 2.4 GHz Microwave Antenna

Ant-P10 $89

COMPACT Semi-Parabolic 2.3 ~ 2.5 GHz, ~ 10.5 dBi gain, ~ 50 ohm impedance. Beamwidth: ~ 30 (H) ~ 60 (V).

Supplied with Tubular Mast Clamp. Dimensions (excludes Socket & Brackets) ~ 275 (W) ~ 90 (H) x ~ 58 mm (D), ~ 235 grams.

Pictured in Vertical Polarity orientation.

SMA female Connector. <Adaptors & Extension Cables>

2.4 GHz Microwave Antenna Vertically Polarised

Ant-P18G $119

Sectional Grid Parabolic, 2.4 ~ 2.5 GHz, ~ 18 dBi gain, ~ 50 ohm impedance Dipole. Beamwidth ~ 25 in vertical polarity mode, Front to Back ratio ~ 20 dB. Fitted with ~ 750 mm RG-8/U Coax cable.

Reflector ~ 390 x ~ 545 mm. Weight ~ 1.7 kilograms. Supplied with Hor/Vert Clamp mounting hardware.

Carriage in an Air Satchel $24, via Post $35.

Pictured in Vertical Polarity orientation * Mast not included. Gold Irridite coated version pictured, we now stock a more durable Galvanised version only.

N male Connector. <Adaptors & Extension Cables>

ADAPTORS

SMA male to N female

SMAm-Nf $10

SMA male to N female. Suitable for P18G antenna.

SMA male to N male

SMAm-Nm $10

SMA male to N male. Suitable for F8N, W9dB, F12, W12dB, F16 & F18 antennas.

 

SMAm-m $10

SMA male to SMA male. Suitable for P10 antenna.

50 centimetre Extension Cable SMA Connector

Cable-178/30 $19

30 cm RG-178 Coax cable with SMA male & female connectors.

~ 4.5 metre Coax Cable

Cable-23/450 $59
~ 450 cm Coax Cable with SMA male & female connectors. Attenuation ~ 0.75 dB/metre @ 2 GHz.

Cable-23/450N $59 not pictured
~ 450 cm Coax Cable with SMA & N male connectors. Attenuation ~ 0.75 dB/metre @ 2 GHz. Suitable for F8N, W9dB, F12, W12dB, F16 & F18 antennas.

Parabolic Yagi & Flat are directional antennas. Whip antennas when used vertically are for most practical purposes omni or non directional.

To maximise 'Range' minimise the length of Coax Cable between Antenna and TX/RX.

Antenna Gain... what does it mean ??? a simplified explanation

Received signal strength from an antenna with 3 dBi gain will be double that from an antenna that has 0 dBi gain, received signal strength from a 6 dBi will be double that from a 3 dBi and so on... An increase in antenna gain of 3 dBi is approximately equal to doubling the transmitter output, received signal strength or range can be increased by raising antenna gain or transmitter output. Range can be doubled by either increasing antenna gain by 6 dBi or quadrupling the transmitter output.

The maximum allowed 2.4 GHz LIPD Video Transmitter output power is 10 milliwatts (mW) EIRP (in Australia), increasing transmitter output is illegal and therefore not an option.

Increasing the gain of the receiver antenna is an alternative to increasing transmitter output.
In very simple terms: increasing antenna gain from 0 dBi to 3 dBi is equivalent to raising the output power of a 10 mW transmitter to ~ 20 mW. (5 dBi to ~ 33 mW) ( 8 dBi to ~ 66 mW) (12 dBi to ~ 160 mW) (15 dBi to ~ 320 mW) (18 dBi to ~ 640 mW) 

* LIPD = Low Interference Potential Devices. * EIRP = Equivalent Isotropically Radiated Power. Source: Australian Communications Authority
Click below for information on Frequencies & Power Limits
http://www.aca.gov.au

Portable LCD TFT Colour Video Monitor 12 VDC or Mains powered with inbuilt Wireless 4 Channel 2.4 GHz AV Receiver & Sequential Switcher & External Audio/Video I/O. Suitable for Wireless or Wired Monitoring including Covert Surveillance, Baby Monitoring, Portable or Multi-Point Surveillance Monitoring, Advertising Displays, etc. Special version with external Antenna input for Long Range up to 10 kilometres using 2 Watt Transmitter & High Gain Antennas.