CCTV Video & Audio 6" Security System Monitor
MONOCHROME VIDEO - AUDIO SURVEILLANCE MONITOR with 2.4 GHz Receiver - Video &
Audio Inputs - VCR Outputs, lightweight Plastic Case. Suitable for Wired &
Wireless Video Cameras, Switchers, Multiplexers, etc etc. DC powered. Use with a
single Wired or Wireless Video Camera for an INSTANT low-cost yet effective
Closed Circuit Television System.
MONOCHROME 6 Inch VIDEO / AUDIO Security System
Monitor with inbuilt 2.4 GHz RECEIVER & VCR I/O
VDC 1.5 Amp Plug Pack + $20
Whip Antenna Folding $20
Flat Antenna $15
Yagi-8 Antenna (Gold
?) (A) $99 / (B) $119
Yagi-12 Antenna (Gold
?) (A) $119 / (B) $139
Yagi-15 Antenna (Gold
?) (A) $149 / (B) $169
Para-18 Antenna (Gold
?) (A) $89 / (B) $99
Para-21 Antenna (Gold
?) (A) $109 / (B) $129
Para-24 Antenna (Gold
?) (A) $149 / (B) $169
23 cm RG-316 Coax Ext Cable SMA male to SMA female $25
50 cm RG-316 Coax Ext Cable SMA male to SMA female $35
5 metre RG-316 Coax Ext Cable SMA male to SMA female $79
4.5 metre RG-223 Coax Ext Cable SMA male to SMA female $89
SMA male to N female Adaptor to suit Para Antennas $10
SMA male to TNC female Adaptor $10
pictured with optional Whip Antenna
Plug-In (Wired) installation when purchased with Plug Pack and Cable/Adaptor
Security System Monitor MONOCHROME - 2.4 GHz
Receiver - Video & Audio & VCR Inputs/Outputs. Lightweight Plastic Case.
Lines Horizontal Resolution (center).
Sensitivity 0.5 to 2.0 v p-p, Negative Sync.
Composite Video Input and Output for CCIR or EIA 75 ohm, compatible with
Australian and USA TV standards.
Line Level Audio Inputs and Output 1 v p-p, 10 000 ohm impedance.
Wireless or Wired input Selection for VCR Playback or Video from a Wired Camera
/ Switcher, Multiplexer, etc.
Outputs for VCR Recording or other purposes.
Wireless: Antenna via female SMA socket at top left back of Case.
Wired: Video and Audio via RCA sockets at rear of Case.
Power Supply: 15 ~ 18 VDC, ~ 1.2 Amps, via 2.1 x 5.5 mm socket at rear of case -
center pin = (+). An optional 12 VDC 1.5 Amp unregulated Plug Pack is available.
Video and Audio for VCR, etc, via RCA sockets at rear of Case.
Front: On/Off push-button Power Switch. Vertical Hold, Brightness and Contrast
under hinged Panel.
Left Side: Sliding Volume Control.
Rear: 50Hz (CCIR, Australia) / 60Hz (EIA, USA) switch. Wired / Wireless input
switch. Channel 1, 2, 3 or 4 select switches.
2.4 ~ 2.483 GHz, 4 channel, Single Channel selection or Automatic Sequential
Switching with ~ 4 second dwell.
Video compatible with TX-MOD 1, TX-MOD 2, TX-MOD 3, TX-ELECTRET, TX-BNC,
HI-POWER TX, TX-CAM IR, TX-CAM, TX-CAM2, TX-CAM2P, TX-RX KitSet V2, TX/RX AV
System and TX/RX AV System II.
Audio compatibility varies and cannot be guaranteed, audio reception may
be fine with some transmitters but not with others.
SMA female Antenna socket, 50 ohms impedance at top left back of Case.
Sensitivity -92 dbm.
mm (W) ~ 142 mm (H) ~ 190 mm (D)
Weight ~ 1.3 kilograms (~ 3.5 kg³ shipping volume)
Plug-In DIY AV 20 metre Cable / Adaptor Set: 20
metre AV Cable with moulded Plugs & Socket. Two RCA Plugs & DC Plug for Camera
end. Two RCA Plugs for Monitor & DC Socket for Camera Plug-Pack. One BNC-RCA
Adaptor for Camera, VCR, Quad, Switcher, Multiplexer, Monitor, Transmitter, etc.