Infrared Light Emitting Diode Illuminators - Ready-to-Use PCB

or coverage. more

Ready-to-Use Plug-In LIGHT EMITTING DIODE INFRA-RED ILLUMINATOR for use with Monochrome & InfraRed sensitive Day/Night Colour Cameras, Automatic On/Off Night/Day.

Sixty Seven 5 mm Light Emitting Diodes, ~ 850 nm wavelength, ~ 15 degree radiation angle, produces a visible dull Red glow.

Main Spot Diameter ~ 0.6 metres @ 3 metres, illuminates ~ 75% of the width-of-vision with a 1/3" Image Sensor & 16 mm Lens.

Power Requirements: 12 Volts DC, ~ 150 milliamps, via 2.1 mm x 5.5 mm DC Socket (center pin +) on ~ 1800 mm Cable. Mains Power Supplies here... use REG12/1A for Maximum Output & reliability.

Construction: Aluminium alloy Case suitable for sheltered outdoor use under eaves etc.

Dimensions: Main Body ~ 70 mm (Dia) x ~ 40 mm. Mass: Lamp ~ 390 grams, Bracket ~ 102 grams.

67 LED Infrared Security Light Illuminator

Bracket included

One Hundred & Forty 5 mm Light Emitting Diodes, ~ 940 nm wavelength, ~ 60º radiation angle, invisible to the naked Eye.

Main Spot Diameter ~ 2.5 metres @ 3 metres, illuminates ~ 75% of the width-of-vision with a 1/3" Image Sensor & 4.3 mm Lens.

Power Requirements: 12 ~ 15 Volts DC, 100 ~ 600 milliamps, via 2.1 mm x 5.5 mm DC Socket (center pin = +) on ~ 40 cm cable.

Mounting Brackets click here * Mains Power Supplies here... use REG15/1.2A for Maximum Output.

Construction: Plastic Case, LEDs & Control PCB are enclosed behind a clear cover, not waterproof but suitable for sheltered outdoor use under eaves etc. Mounting: 1/4" UNC female thread at rear and compatible with Mounting Brackets on this page.

Dimensions: ~ 120 mm (W), ~ 160 mm (H), ~ 39 mm (D). Mass: ~ 260 grams.

Covert Invisible to human eye

Infrared LED CCTV Illuminator for use with Monochrome & Day-Night Colour Closed Circuit Television video surveillance cameras. 940 nanometre wavelength invisible to the naked Eye. 60 degree radiation angle closely matches the angle of view of 3.6 mm focal length lens & 1/3 CCD when Infra-Red Illuminator is mounted alongside camera. Infrared Illuminator may be mounted behind camera when using shorter focal length lenses or several Illuminators may be used to illuminate wider areas. When monochrome Cameras are fitted with an Infrared Pass Filter images will be sharper in normal visible light and will be sharply focussed with Infra-Red Illumination only. Use Infrared Long Pass Filter Sheets to make-your-own HIGH OUTPUT Incandescent Infrared Illuminator and/or to conceal Video Camera or LED Illuminator.

Bracket not included

One Hundred & Seven 8 mm Light Emitting Diodes, ~ 850 nm wavelength, ~ 45 degree radiation angle, produces a visible dull Red glow.

Main Spot Diameter ~ 1.8 metres @ 3 metres, illuminates ~ 75% of the width-of-vision with a 1/3" Image Sensor & 6 mm Lens.

Power Requirements: 12 Volts DC, ~ 600 milliamps, via 2.1 mm x 5.5 mm DC Socket (center pin +) on ~ 600 mm Cable that exits through Mounting Bracket base. Mains Power Supplies here... use REG12/1A for Maximum Output & reliability.

Construction: Aluminium alloy Case suitable for sheltered outdoor use under eaves etc.

Dimensions: ~ 150 mm (W), ~ 100 mm (H), ~ 202 mm (D) front to back with Bracket in straight position. Mass: ~ 900 grams.

Integral Bracket included

Ready-to-Use Plug-In LIGHT EMITTING DIODE INFRA-RED ILLUMINATOR for use with Monochrome & InfraRed sensitive Day/Night Colour Cameras, Automatic On/Off Night/Day.

Eighty Three Light Emitting Diodes, ~ 850 nm wavelength, ~ 80º radiation angle, produces a visible dull Red glow.

Main Spot Diameter ~ 3.6 metres @ 3 metres, illuminates ~ 75% of the width-of-vision with a 1/3" Image Sensor & 2.9 mm Lens.

Power Requirements: 12 Volts DC or 24 volts ac, ~400 mA DC / ~250 mA ac. Mains Power Supplies here.... use REG12/1A or PS24/2A for long cable runs.

Construction: Aluminium Housing, suitable for sheltered outdoor use under eaves etc.

Dimensions: Click on drawing. Mass: ~ 880 grams, Bracket ~ 150 grams.

Mounting Bracket included

Infrared LED CCTV Illuminator for Monochrome Colour Day-Night Closed Circuit Television video surveillance cameras 850 nanometre wavelength Infrared Illuminator may be mounted behind camera when using shorter focal length lenses or several Illuminators may be used to illuminate wider areas monochrome Cameras fitted with an Infrared Pass Filter images will be sharper in normal visible light and will be sharply focussed with Infra-Red Illumination only

click here or on image to view full size

Ready-to-Use 8 Watt Infrared LIGHT EMITTING DIODE PCB IR Lamp for Monochrome & InfraRed sensitive Day/Night colour Cameras.

Thirty Six 5 mm Infrared Light Emitting Diodes, ~ 850 nm wavelength, ~ 70º radiation angle, produces a visible dull Red glow.

Main Spot Diameter ~ 3 metres @ 3 metres, illuminates ~ 75% of the width-of-vision with a 1/3" Image Sensor & 3.6 mm Lens.

*Power Requirements: Up to 12 Volts DC, ~ 650 milliamps @ 12 Volts, 2.1 x 5.5 mm DC Socket (center pin = +) on ~ 300 mm cable. PCB ~ 75 x ~ 90 mm (can be 'cut' to 75 x 82), 50 mm 'Hole'.

Ready-to-Use Infrared LIGHT EMITTING DIODE PCB Lamp for InfraRed sensitive Cameras. Light Dependent Resistor & Transistors control LED current which is maximum when 'Visible' illumination on LDR sensor is near zero.

Twenty 5 mm Infrared Light Emitting Diodes, ~ 850 nm wavelength, ~ 70º radiation angle, Main Spot Diameter ~ 3 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC, ~ 90 milliamps via 2-pin socket on back of PCB (matching Plug with ~ 50 mm Wires included, 'Red' wire is positive. PCB ~ 45 mm Diameter, ~ 14 mm Deep excluding socket, ~ 18 mm 'Hole'.

click image to enlarge

Ready-to-Use Infrared LIGHT EMITTING DIODE PCB Lamp for InfraRed sensitive Cameras. Light Dependent Resistor & Transistors control LED current which is maximum when illumination "Visible or Infrared" on LDR sensor is near zero.

Twelve 5 mm Infrared Light Emitting Diodes, ~ 850 nm wavelength, ~ 60º radiation angle, Main Spot Diameter ~ 2.5 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC, ~ 120 milliamps via 2-pin socket on back of PCB (matching Plug not stocked), 'Black' mark on socket indicates negative terminal. PCB ~ 42 mm Diameter, ~ 12 mm Deep excluding socket, ~ 20 mm 'Hole'.

click image to enlarge

Twenty Four 5 mm Infrared Light Emitting Diodes, ~ 850 nm wavelength, ~ 60º radiation angle, Main Spot Diameter ~ 2.5 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC, ~ 150 milliamps via 2-pin socket on back of PCB (matching Plug with ~ 50 mm Wires included, 'Red' wire is positive. PCB ~ 45 mm Diameter, ~ 14 mm Deep excluding socket, ~ 18 mm 'Hole'.

click image to enlarge

Twelve 5 mm Infrared Light Emitting Diodes, ~ 850 nm wavelength, ~ 70º radiation angle, Main Spot Diameter ~ 3 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC. PCB ~ 60 mm Diameter, ~ 14 mm Deep excluding socket, ~ 31 mm 'Hole'.

click image to enlarge

Eighteen Infrared Light Emitting Diodes nine 5 mm & nine 8 mm, ~ 850 nm wavelength, ~ 60º radiation angle, Main Spot Diameter ~ 2.5 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC. PCB ~ 70 mm Diameter, ~ 16 mm Deep excluding socket, ~ 46 mm 'Hole'.

click image to enlarge

Fifty Six Infrared 5 mm Light Emitting Diodes, ~ 850 nm wavelength, ~ 60º radiation angle, Main Spot Diameter ~ 2.5 metres @ 3 metres. produces a visible dull Red glow.

Power Requirements: 12 Volts DC. PCB ~ 74 mm Diameter, ~ 16 mm Deep excluding socket, ~ 44 mm 'Hole'.

click image to enlarge

discontinued

Cat Code: IR-ILLUM/2 only $149 ! Ready-to-Use Super Infrared LED Illuminator for Monochrome & InfraRed sensitive Day/Night Colour Cameras. SEVEN 10 mm SUPER Light Emitting Infra Red Diodes, ~ 850 nm wavelength, ~ 20º radiation angle, produces a visible dull Red glow.

Main Spot Diameter: ~ 1 metre @ 3 metres. Illuminates ~ 80% of the width-of-vision with 1/3" Image Sensor & 12 mm Lens.
Range & Level-of-Illumination are affected by: *Power-Input, Lens Transmittance, Camera/Sensor Sensitivity & Spectral Response.

Control: Automatic On/Off Night/Day. *Power Requirements: 12 ~ 15 Volts DC, 80 ~ 310 milliamps via stripped & tinned wires, ~ 750 mm Cable. Mounting Brackets click here * Mains Power Supplies here.... use REG15/1.2A for Maximum Output. Construction: Aluminium & Plastic, not waterproof but suitable for sheltered outdoor use under eaves etc.

Mounting: 1/4" UNC female thread at bottom and compatible with Camera Mounting Brackets. Dimensions: ~ 138 mm x ~ 145 mm, ~ 850 grams.

Ready-to-Use Hi-Power LIGHT EMITTING DIODE infra red light Illuminator for Monochrome & InfraRed sensitive Day/Night colour Cameras

discontinued

Cat Code: IR-LEDkit/850 $49 - 'Kit' 52 mm Diameter 50 LED Round Infrared Lamp Kit - PCB, LEDs, Housing & Assembly Notes. Wavelength / Angle: ~ 850 nm, ±7º (14º)

Max Radiant Intensity: ~ 200 mW/sr @ Max 100 mA Visibility @ Max current: Dull Red Glow Forward Voltage at Max Current for 5 LEDs in series = ~ 10.5 volts. Main Spot Diameter: ~ 0.74 metres @ 3 metres. PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

Construction of Five Group Lamp is straightforward. Ten Group Lamp requires extra care as 25 LEDs are inserted backwards. The edges of some LEDs may need to be filed. It may not be possible to operate Infra-Red LEDs continuously at Max Current due to heat.

discontinued

Cat Code: IRLEDkit-940/20 $29 - 'Kit' 52 mm Diameter 50 LED Round Infra Red Light Kit - PCB, LEDs, Housing & Assembly Notes. Wavelength / Angle: ~ 940 nm, ±10º (20º) Max Radiant Intensity: ~ 120 mW/sr @ Max 100 mA Visibility @ Max current: Just perceptible.

Forward Voltage at Max Current for 5 LEDs in series = ~ 7 volts. Main Spot Diameter: ~ 1.06 metres @ 3 metres. PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

INFRA RED LONG PASS FILTER SHEETS Make a Higher Output INCANDESCENT Illuminator

CCTV Infrared Lamp Illuminator Lamp for Closed Circuit Television monochrome video surveillance cameras High Output 850 nanometre suits SONY Low Noise High Sensitivity HAD CCD Image Sensor in IR sensitive video cameras 14 to 70 degree radiation angles Infrared Lamp Illuminator mount alongside camera or several IR Lamps to illuminate large areas use with an Infrared Pass filter for sharp focus

discontinued

Cat Code: IRLEDkit-940/40 $29 - 'Kit' 52 mm Diameter 50 LED Round Infrared Lamp Kit - PCB, LEDs, Housing & Assembly Notes. Wavelength / Angle: ~ 940 nm, ±20º (40º) Max Radiant Intensity: ~ 90 mW/sr @ Max 100 mA

Visibility @ Max current: Just perceptible. Forward Voltage at Max Current for 5 LEDs in series = ~ 7 volts. Main Spot Diameter: ~ 2.1 metres @ 3 metres. PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

Infrared Application Notes

INFRA RED LONG PASS FILTERS for Lenses

SEE-in-the DARK Camera with Inbuilt InfraRed LEDs Colour Day/Night IR Camera