J High Resolution
Infrared See-in-the-Dark night vision day night camera.
J Quality DSP Chipset for Best Image
J ~ 700 H-Pixels.
~ 0.5 Lux.
48 + dB Signal : Noise Ratio.
Rugged Aluminium Housing.
HIGH 700 + H-Pixel * SEE-in-the-DARK
18 IR LEDs * night
vision day night camera Wall / Ceiling 4 mm Lens, inbuilt Infra-Red LEDs,
⅓" PANASONIC CCD, Rugged Aluminium
Housing, Glass Lens Cover, Swivel & Tilt adjustment.
This Camera is ideal for most common
Surveillance applications and for 'disturbance-free' observation (in total
darkness) of Babies, Convalescing, Birds, Animals, etc., while Sleeping,
Recuperating, Nesting, Calving, etc.
Surveillance System suitable
for average to zero illumination levels in
Homes, Shops, Showrooms, Offices, Warehouses, sheltered, shaded & evenly
lit outdoor use under eaves, etc.
DIY Plug-In installation when purchased
DIY Plug-In 20 metre Video & Power Cable &
REG12/0.3A Plug Pack.
|No optional Lenses for this Camera
|All values are
|Width of Vision
with 4 mm Lens fitted to Camera |
|6 m |
Video System: PAL fully
compatible with Australian TV System.
753 (H) x 582 (V) 438
246 Pixel ⅓" PANASONIC Interline Transfer
LOW BLEMISH CCD
Sensor, due to the sensitive nature of the chip manufacturing process there may
be more imperfections in the photodiodes in this Special CCD Image Sensor than
in an ordinary sensor.
Day / Night Infrared Light Emitting Diode
CCTV Infrared Night Vision information
Lens: Board Type 4 mm Focal Length,
there are no Accessory Lenses for this Camera,
Scanning System: 2 : 1
Interlace PAL 50 Hz vertical, 15 625 Hz horizontal.
Video Output: 1.14 V
p-p Composite Video 75 ohms, suit Australian TV, VCR, AV & Video inputs, BNC
socket on ~ 30 cm cable.
Horizontal Pixels: 700
+ (this value is provided for comparative purposes only) Better than VHS &
better than Super-VHS resolution.
Sensitivity: ~ 0.5 lux
@ F1.2 (this value is provided for comparative purposes only), 0 lux with LEDs
'ON'. Infrared LEDs illuminate ~ 95% of the Width-of-Vision and are effective up
to approximately 10 m depending on the reflective characteristics of subject.
Light Emitting Diodes:
Twenty One ~ 850 nm wavelength Infrared, these produce a dull Red visible glow.
Automatic Light Sensor switches LEDs On/Off depending on light level.
Shutter (AES): 1/50 to 1/100 000 second, 20 milliseconds to 10 microseconds,
Automatic Gain Control:
Back Light Compensation
~ 400 to ~ 1000 nm with an Infrared 'CUT' Notch
between approximately 720 ~ 830 nm,
Signal to Noise ratio:
48 + dB, measured with AGC off.
Power Requirements: 12
Volts DC Regulated, ~ 400 milliamps with LEDs On, 2.1 x 5.5 mm DC socket, center
pin = (+), ~
30 cm cable.
Dimensions: ~ 47 x ~ 75
x 95 mm, ~ 280 grams.
Made in Taiwan in an
ISO 9001 certified factory.
Experience: 18 + Years.
Day Night Colour Infrared Light Emitting Diode (Night Vision) Cameras
Colour CCTV Day Night Cameras with
inbuilt Infrared Light Emitting Diodes "See-in-the-Dark" and produce images
when visible illumination is zero.
At average levels of illumination
these Cameras produce Colour images, depending on their sensitivity (Lux) at
low illumination levels and in total darkness the image is Monochrome.
These Cameras generally have a
relatively high sensitivity image sensor and
Fixed Iris Lens
therefore under high illumination levels images will be overexposed for the
here, an exception is
MINI-COL-IR which has a special Wide Dynamic Range allowing it to cope
with higher illumination levels than ordinary Cameras.
Ordinary CCTV Colour Cameras are
relatively insensitive to Infrared because they have an IR CUT Filter
between the Lens and Image Sensor, this filter excludes Infrared radiation
with a wavelength greater than ~ 700 nm that would otherwise adversely
affect White Balance, Colour Rendition and Image Sharpness.
Day / Night Colour CCTV Cameras are
sensitive to Infrared because they either do not have an IR CUT Filter or
utilise a special NOTCH IR CUT Filter that excludes the wavelengths most
harmful to colour quality (720 ~ 830 nm) from reaching the Image Sensor.
A Colour Camera that does not have
an IR CUT Filter usually has poor
colour rendition characterised by a Pink-Red
'tint' when the illumination is InfraRed rich, use of
a 'Notch' Filter helps however White Balance, Colour Rendition and Image
Sharpness are compromised for Infrared sensitivity. (Image Sharpness can be
restored by using a specially designed Lens that corrects the focus shift
between Visible and Infrared)
The IDEAL Day / Night Infrared
Sensitive Colour CCTV Camera would utilise an
Automatic Iris Lens to cope with high illumination levels and the Lens
would also have a large aperture (low 'F' number) to maximise light
transmission when illumination levels are low * it would also utilise a
Traditional IR CUT Filter when illumination levels are adequate for Colour
and then REMOVE the IR CUT Filter when levels are low
CCS-IRdnWD have these features and are recommended
for OPTIMUM results - the ULTIMATE SOLUTION is
DomePTZ-dn these also have Automatic-Focus to
ensure crisp images under all conditions.
Infrared rich light sources include
Daylight and most Filament type lamps including common Spot lamps, Tungsten
lamps, Halogen lamps, etc.
The majority of Light emitted from
'Cold' type sources such as Fluorescent, Mercury Vapour, Sodium Vapour,
etc., is visible, these sources contain little Infrared energy.
Infrared capability is a trade-off that affects Colour Quality particularly
in "Infrared Rich" environments.
Resolution night vision day night camera CCTV Video Surveillance Infrared Camera
High Sensitivity SEE in the DARK with Infrared LED Panasonic CCD Image Sensor
for average to zero light levels in Homes Offices Showrooms for discreet
surveillance Board lens for sharper focus & better results in low light & with