Bracket pictured not included

Cat Code: IR-ILLUM $99

Cat Code: IR-ILLUM/ON - SPECIAL version with IR LEDs always ON $119

(Ideal for difficult Back-Lit entrance type situations with Mono or InfraRed sensitive Day/Night Colour Cameras)

Ready-to-Use Plug-In 9 Watt 140 LIGHT EMITTING DIODE INFRA-RED ILLUMINATOR for Monochrome & InfraRed sensitive Day/Night Colour Cameras.

Light Emitting Diodes: 140 pieces, 940 nm wavelength, 60º radiation angle, invisible to the naked Eye.

Main Spot Diameter:  ~ 3.2 metres @ 3 metres. Illuminates ~ 80% of the width-of-vision with 1/3" Image Sensor & 3.6 mm Lens.

Control: Automatic On/Off Night/Day.

Range & Level-of-Illumination are affected by: *Power-Input, Lens Transmittance, Spectral Response & Sensitivity of Lens/Camera.

*Power Requirements: 12 ~ 15 Volts DC, 100 ~ 600 milliamps, via 2.1 mm x 5.5 mm DC Socket (center pin = +) on ~ 40 cm cable.

Mounting Brackets click here * Mains Power Supplies here... use REG15/1.2A for Maximum Output.

Construction: Plastic Case, LEDs & Control PCB are enclosed behind a clear cover, not waterproof but suitable for sheltered outdoor use under eaves etc.

Mounting: 1/4" UNC female thread at rear and compatible with Camera Mounting Brackets. Dimensions: ~ 120 mm x ~ 160 mm x ~ 39 mm, ~ 260 grams.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when the Camera and Illuminator are positioned at the same distance from subject). more

Mounting Bracket included

click here or on image to view full size

Cat Code: IR-Illum850 only $149 !

Ready-to-Use LED Illuminator for Monochrome & InfraRed sensitive Day/Night Colour Cameras.

Eighty Three Light Emitting Diodes, ~ 850 nm wavelength, ~ 80º radiation angle, produces a visible dull Red glow.

Main Spot Diameter: ~ 4 metres @ 3 metres. Illuminates ~ 100% of the width-of-vision with 1/3" Image Sensor & 2.9 mm Lens.

Range & Level-of-Illumination are affected by: Lens Transmittance, Camera/Sensor Sensitivity & Spectral Response.

Control: Automatic On/Off Night/Day.

Power Requirements: 12 Volts DC or 24 volts ac, ~400 mA DC / ~250 mA ac. Mains Power Supplies here.... use REG12/1A or PS24/2A for long cable runs.

Construction: Aluminium Housing, suitable for sheltered outdoor use under eaves etc.

Dimensions/Weight: Click on drawing at left. ~ 880 grams. Bracket ~ 150 grams.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when the Camera and Illuminator are positioned at the same distance from subject). more

Cat Code: IR36-PCB only $39 !

Ready-to-Use 8 Watt Infrared LIGHT EMITTING DIODE PCB IR Lamp for Monochrome & InfraRed sensitive Day/Night colour Cameras.

Infrared Light Emitting Diodes: 36 pieces, ~ 850 nm wavelength, ~ 70º radiation angle, produces a visible dull Red glow.

Main Spot Diameter:  ~ 2.5 metres @ 3.5 metres. Illuminates ~ 90% of the width-of-vision with 1/3" Image Sensor & 6 mm Lens.
Range & Level-of-Illumination are affected by: *Power-Input, Lens Transmittance, Camera/Sensor Sensitivity & Spectral Response.

*Power Requirements: Up to 12 Volts DC, ~ 650 milliamps @ 12 Volts, 2.1 x 5.5 mm DC Socket (center pin = +) on ~ 300 mm cable. PCB ~ 75 x ~ 90 mm (can be 'cut' to 75 x 82), 50 mm 'Hole'.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when Camera and Illuminator are positioned at the same distance from subject and illumination of full width is required). more

discontinued

Cat Code: IR-ILLUM/2 only $149 !

Ready-to-Use Super Infrared LED Illuminator for Monochrome & InfraRed sensitive Day/Night Colour Cameras.

SEVEN 10 mm SUPER Light Emitting Infra Red Diodes, ~ 850 nm wavelength, ~ 20º radiation angle, produces a visible dull Red glow.

Main Spot Diameter:  ~ 1 metre @ 3 metres. Illuminates ~ 80% of the width-of-vision with 1/3" Image Sensor & 12 mm Lens.
Range & Level-of-Illumination are affected by: *Power-Input, Lens Transmittance, Camera/Sensor Sensitivity & Spectral Response.

Control: Automatic On/Off Night/Day.

*Power Requirements: 12 ~ 15 Volts DC, 80 ~ 310 milliamps via stripped & tinned wires, ~ 750 mm Cable.

Mounting Brackets click here *  Mains Power Supplies here.... use REG15/1.2A for Maximum Output.

Construction: Aluminium & Plastic, not waterproof but suitable for sheltered outdoor use under eaves etc.

Mounting: 1/4" UNC female thread at bottom and compatible with Camera Mounting Brackets. Dimensions:  ~ 138 mm x ~ 145 mm, ~ 850 grams.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when the Camera and Illuminator are positioned at the same distance from subject). more

discontinued

Cat Code: IR-LEDkit/850 $49 - 'Kit'

52 mm Diameter 50 LED Round Infrared Lamp Kit - PCB, LEDs, Housing & Assembly Notes.

Wavelength / Angle: ~ 850 nm,  ±7º (14º)

Max Radiant Intensity: ~ 200 mW/sr @ Max 100 mA

Visibility @ Max current: Dull Red Glow

Forward Voltage at Max Current for 5 LEDs in series = ~ 10.5 volts.

Main Spot Diameter:  ~ 0.74 metres @ 3 metres.

PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

Construction of  Five Group Lamp is straightforward. Ten Group Lamp requires extra care as 25 LEDs are inserted backwards. The edges of some LEDs may need to be filed.

It may not be possible to operate Infra-Red LEDs continuously at Max Current due to heat.

Range is affected by Lens Transmittance, Camera Sensitivity & Spectral Response of Image Sensor/Camera.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when Camera and Illuminator are positioned at the same distance from subject and illumination of full width is required).

discontinued

Cat Code: IRLEDkit-940/20 $29 - 'Kit'

52 mm Diameter 50 LED Round Infra Red Light Kit - PCB, LEDs, Housing & Assembly Notes.

Wavelength / Angle: ~ 940 nm,  ±10º (20º)

Max Radiant Intensity: ~ 120 mW/sr @ Max 100 mA

Visibility @ Max current:  Just perceptible.

Forward Voltage at Max Current for 5 LEDs in series = ~ 7 volts.

Main Spot Diameter:  ~ 1.06 metres @ 3 metres.

PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

Construction of  Five Group Lamp is straightforward. Ten Group Lamp requires extra care as 25 LEDs are inserted backwards. The edges of some LEDs may need to be filed.

It may not be possible to operate Infra-Red LEDs continuously at Max Current due to heat.

Range is affected by Lens Transmittance, Camera Sensitivity & Spectral Response of Image Sensor/Camera.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when Camera and Illuminator are positioned at the same distance from subject and illumination of full width is required).

discontinued

Cat Code: IRLEDkit-940/40 $29 - 'Kit'

52 mm Diameter 50 LED Round Infrared Lamp Kit - PCB, LEDs, Housing & Assembly Notes.

Wavelength / Angle: ~ 940 nm,  ±20º (40º)

Max Radiant Intensity: ~ 90 mW/sr @ Max 100 mA

Visibility @ Max current: Just perceptible.

Forward Voltage at Max Current for 5 LEDs in series = ~ 7 volts.

Main Spot Diameter:  ~ 2.1 metres @ 3 metres.

PCB tracks are arranged as Five Groups of 10 series connected LEDs. Interconnections may be rearranged to create Ten Groups of 5 series connected LEDs. Groups are paralleled and a series resistor used to limit total current.

Construction of  Five Group Lamp is straightforward. Ten Group Lamp requires extra care as 25 LEDs are inserted backwards. The edges of some LEDs may need to be filed.

It may not be possible to operate Infra-Red LEDs continuously at Max Current due to heat.

Range is affected by Lens Transmittance, Camera Sensitivity & Spectral Response of Image Sensor/Camera.

Best results will be achieved by matching the 'Lens' Horizontal Angle-of-View and the LED Radiation Angle (when Camera and Illuminator are positioned at the same distance from subject and illumination of full width is required).